Sell Happymodel CrazybeeX V2.2 F4 1-2S AIO (25.5x25.5) Flight Controller for Crux3 Toothpick Whoop - Flysky HPV22-FL best price

Happymodel CrazybeeX V2.2 F4 1-2S AIO (25.5x25.5) Flight Controller for Crux3 Toothpick Whoop - Flysky HPV22-FL Introduction: CrazybeeX series flight controller is the first 5in1 AIO flight controller which could handle 2s. It's a better upgrade flight controller for your whoops. - Use to build a 1-2S compatible lightest 65mm/75mm/85mm brushless whoop or  2-3 inch ultra light toothpick. Specification: Item Name: CrazybeeX FRSKY V2.2 Flight Controller 1-2s Receiver：FLYSKY Flight controller: MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1S-2S battery input (DC 2.9V-8.7V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in 5V 1A BEC Built-in voltage detection Firmware target: CrazybeeX FS version: Recommend Betaflight 3.5.7 target CRAZYBBEF4FS Onboard 4in1 ESC: EFM8BB21 Power supply: 1-2S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_7.HEX Default protocol: DSHOT600 (CrazybeeX FS V2.2 version) Onboard Flysky SPI receiver SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m Failsafe support Onboard 5.8g VTX: Output power: 25mw~200mw switchable Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels With Race band Smartaudio ready Default vtx_power is 3 Should set vtx_low_power_disarm = ON to reduce the high temperature when test on the ground Onboard Voltage and Current detector: Voltage Meter scale “110” Amperage Mete scale “1175” CrazybeeX FS V2.2 Bind procedure: 1. Make the on board receiver get into bind mode: For 3.5.7 version firmware Press and hold the bind button for 1 second ,then plug USB, the Red LED at the bottom of the flight controller will blinking fast , this indicate the receiver is in bind mode; For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED at the bottom of the flight controller will blinking fast , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx” 2. Make your Flysky transmitter get into bind mode . If bind is successful the red led will getting to be solid. SPI Receiver option: A7105_FLYSKY_2A compatible with Flysky AFHDS-2A protocol A7105_FLYSKY compatible with Flysky AFHDS protocol Package Included: 1x CrazybeeX FLYSKY V2.2 Flight Controller 4x Anti-Vibration Ball 4x Screws